Tutorial 4: Step-by-Step Guide in Designing and Optimization of a PCB 4G and 5G Antenna
4.1 Introduction
Welcome to tutorial 4 in the practical RF design tutorial series. In this tutorial, we will learn the complete design and optimization guide for a 4G and 5G antenna. This antenna is implemented on a Rigid Printed Circuit Board (PCB).
Table 4.1: Antenna Design Steps
Table 4.1 shows the Antenna design steps. We will start our presentation by giving an introduction to the antenna. The first step of designing an antenna is antenna selection. The next step is to design the selected antenna. The third step is to optimize the antenna, followed by antenna EM simulation. Finally, the results of the antenna will be analyzed.
4.1.1 Antenna Introduction

Figure 4.1: Basic Radio Architecture
Figure 4.1 shows the basic radio architecture. The basic RF radio system contains a Baseband Processor, Up-Conversion Mixer, Down-Conversion Mixer, Voltage Controlled Oscillator (VCO), Local Oscillator (LO) or Frequency Generating Unit (FGU), Pre-Driver, Driver, Final Power Amplifier (PA), Coupler, Power Controller, Antenna Switch, Harmonic Filter, Antenna, Preselector Filter, Low Noise Amplifier (LNA) and Post-Selector Filter. Each radio component plays a unique and significant part in achieving the end goal of receiving and transmitting information wirelessly over a long distance.
In Figure 4.1, the antenna is the first component from the right of a radio system. The antenna is used to transmit and receive signals. The signal received by the antenna will be routed to the receiver section by the antenna switch. In the same way, the signal to be transmitted will be routed to the antenna via an antenna switch.
Webster’s Dictionary defines an antenna as a metallic device, either a rod or wire, for radiating or receiving radio waves. The IEEE Standard Definitions of Terms for Antennas (IEEE Std 145–1983) defines the antenna or aerial as “a means for radiating or receiving radio waves.” The antenna is the transitional structure between free space and a guiding device.
4.1.2 What does an antenna do?
The antenna acts as a transducer that converts electromagnetic waves to electrical energy and vice versa. The process is bi-directional.
If an alternating current is applied, the antenna will produce an electromagnetic field surrounding the structure.
When these electromagnetic waves hit a receiving antenna, they will induce a current on the antenna surface, which will then be converted to the message by the receiving radio.
4.1.3 Antenna Types
There are six types of antennas. These are Wire antennas, Aperture antennas, Microstrip antennas, Array antennas, Reflector antennas, and Lens Antennas.
4.1.3.1 Wire Antenna
There are various shapes of wire antennas, such as a straight wire (dipole), loop, and helix, which are shown in Figure 4.2. Loop antennas need not only to be circular. They may take the form of a rectangle, square, ellipse, or any other configuration. The circular loop is the most common because of its simplicity in construction.

Figure 4.2: Wire Antenna Configurations
4.1.3.2 Aperture Antenna
Figure 4.3 shows Aperture antenna configurations. Antennas of this type are very useful for aircraft and spacecraft applications because they can be very conveniently flush-mounted on the skin of the aircraft or spacecraft. In addition, they can be covered with a dielectric material to protect them from hazardous conditions of the environment.


Figure 4.3: Aperture antenna configurations
4.1.3.3 Microstrip Antenna
These antennas consist of a metallic patch on a grounded substrate. The metallic patch can take many different configurations, as shown in Figure 4.4. However, the rectangular and circular patches, shown in Figure 4.4, are the most popular because of their ease of analysis and fabrication and their attractive radiation characteristics, especially low cross-polarization radiation.

Figure 4.4: Representative shapes of microstrip patch elements.
The microstrip antennas are low profile, comfortable to planar and nonplanar surfaces, simple and inexpensive to fabricate using modern printed-circuit technology, mechanically robust when mounted on rigid surfaces, compatible with MMIC designs, and very versatile in terms of resonant frequency, polarization, pattern, and impedance. These antennas can be mounted on the surface of high-performance aircraft, spacecraft, satellites, missiles, cars, and even handheld mobile telephones.
4.1.3.4 Array Antenna
The arrangement of the array may be such that the radiation from the elements adds up to give maximum radiation in a particular direction or directions, minimum in others, or otherwise as desired. Typical examples of arrays are shown in Figure 4.5. Usually, the term array is reserved for an arrangement in which the individual radiators are separate, as shown in Figure 4.5 (a–c). However, the same term is also used to describe an assembly of radiators mounted on a continuous structure, as shown in Figure 4.5 (d).

Figure 4.5: Typical wire, aperture, and microstrip array configurations.
4.1.3.5 Reflector Antenna
A very common antenna form for such an application is a parabolic reflector, shown in Figures 4.6 (a) and (b). Antennas of this type have been built with diameters as large as 305 m. Such large dimensions are needed to achieve the high gain required to transmit or receive signals after millions of miles of travel. Another form of a reflector, although not as common as the parabolic, is the corner reflector, shown in Figure 4.6 (c).

Figure 4.6: Typical reflector configurations
4.1.3.6 Lens Antenna
Lenses are primarily used to collimate incident divergent energy to prevent it from spreading in undesired directions. By properly shaping the geometrical configuration and choosing the appropriate material for the lenses, they can transform various forms of divergent energy into plane waves. They can be used in most of the same applications as parabolic reflectors, especially at higher frequencies. Their dimensions and weight become exceedingly large at lower frequencies. Lens antennas are classified according to the material from which they are constructed or according to their geometrical shape. Some forms are shown in Figure 4.7.

Figure 4.7: Typical lens antenna configurations. (SOURCE: L. V. Blake, Antennas, Wiley, New York, 1966).
4.1.4 Antenna Parameters
In this section, the definition of antenna parameters will be given.
- Return Loss – Return loss is the measure of how well the impedance of an antenna matches the impedance of the transmission line or source to which it is connected.
- Gain – The gain is the amount of power radiated in a specific direction relative to a power source that radiates equally in all directions.
- Directivity –Directivity is a key parameter that describes how well an antenna focuses its radiated power in a particular direction. Directivity is the ratio of the radiation intensity in a given direction from the antenna to the radiation intensity averaged over all directions. It measures how directional an antenna’s radiation pattern is compared to an isotropic radiator.
- Radiation Pattern – An antenna radiation pattern is the graphical representation of the radiation properties of an antenna in its radiating far-field region.
- Cross Polarization level – Cross polarization level in antenna theory refers to the undesired polarization component that is orthogonal to the intended polarization of an antenna. The cross-polarization level is a measure of how much energy an antenna radiates or receives in the polarization orthogonal to its intended polarization. It’s typically expressed as the ratio of the power in the undesired polarization to the power in the desired polarization.
- Axial Ratio – Axial ratio is a parameter used to describe the polarization of an antenna, particularly for circularly polarized antennas. It’s defined as the ratio of the major axis to the minor axis of the polarization ellipse.
- Radiation Efficiency – Radiation efficiency is the ratio of the power radiated by an antenna to the power input to the antenna. It represents how effectively the antenna converts the input power into radiated electromagnetic waves.
- Total Efficiency – Total efficiency is overall efficiency that takes into account both the radiation efficiency and the impedance matching efficiency of the antenna.
- Beamwidth – Beamwidth is a measure of the directional properties of an antenna’s radiation pattern. Beamwidth is the angular separation between two points in an antenna’s radiation pattern where the power drops to half or -3 dB of its maximum value in the main lobe.
- Sidelobe Ratio – Sidelobe ratio, also known as sidelobe level, is a measure of the relative strength of an antenna’s side lobes compared to its main lobe. The sidelobe ratio is the ratio of the power density in the antenna’s strongest side lobe to the power density at the peak of the main lobe, usually expressed in decibels or dB.
4.1.4.1 Antenna System Parameters
- Effective Radiated Power (ERP) – ERP (Effective Radiated Power) is a calculated measurement that describes the peak transmitted power output of the system.
- SAR – SAR is an acronym for Specific Absorption Rate. It is the merit of performance for which a governmental agency has specified safety limits on Human Exposure to RF radiation.
4.1.5 Antenna Implementation Techniques
Table 4.2 shows antenna implementation techniques, PCB implementation, and chip implementation. The advantages of PCB implementation are cost-saving and simplifying manufacturing and assembly processes. The disadvantage is that PCB antennas are susceptible to interference from nearby components and are generally large.
The tiny chip antennas allow easy integration into compact devices and surface-mount technology compatibility for PCBs. However, the performance of the chip antenna is also affected by nearby objects and ground planes, as well as limited bandwidth and radiation pattern options.
- Implementation Technique
- On-Board PCB Antennas
- Simplifies manufacturing and assembly processes.
- Advantages
- Integration is directly on the PCB, saving on costs.
- Simplifies manufacturing and assembly processes.
- Disadvantages
- Susceptible to interference from nearby components.
- Large size
- Implementation Technique
- Chip Antennas
- SMT (surface-mount technology) compatibility for PCBs.
- Limited bandwidth and radiation pattern options.
- Advantages
- The tiny size allows easy integration into compact devices.
- SMT (surface-mount technology) compatibility for PCBs.
- Limited bandwidth and radiation pattern options.
- Disadvantages
- Lower gain and efficiency compared to larger antennas.
- Performance is affected by nearby objects and ground planes.
- Limited bandwidth and radiation pattern options.
- Dipole Antenna
- Loop Antenna
- Helical Antenna
- Yagi-Uda Antenna
- Spiral Antenna
- Corner Reflector Antenna
- Parabolic Reflector Antenna
- Patch Antenna
- PIFA Antenna
- Bow Tie Antenna
- Log-Periodic Antenna
- Slot Antenna
- Cavity-Backed Slot Antenna
- Monopole Antenna
- Inverted-F Antenna
- Slotted Waveguide Antenna
- Horn Antenna
- Vivaldi Antenna
- Telescopes Antenna
- Fractal Antenna
- NFC Antenna
The question is, how do you select an antenna for your application? To choose an antenna for your application, you need to ask these questions;
- Size of the product?
- Radiation pattern requirement? Directional or Omnidirectional Radiation Patterns?
- Is there any Polarization requirement? Circular, Linear, or Elliptical polarization?
- Antenna implementation? Is it implemented on a PCB or ceramic chip?
For our application, we selected an Inverted F antenna. Since the antenna is to be implemented on a PCB, it’s called a Planar Inverted F Antenna (PIFA).
4.3 Step 2: Antenna Design
PIFA antenna design will be demonstrated in this section.
4.3.1 Design of conformal antennas for telephone handsets
The Planar inverted F antenna is a famous antenna that is widely used for telephone handsets. Figure 4.8 shows the Inverted-L Antenna and Inverted-F Antenna on the left and right, respectively.

Figure 4.8: The Inverted-L Antenna (left) and the Inverted-F Antenna
- Inverted-L Antenna
- Has a horizontal element with 1/4 wavelength.
- The vertical element is a fraction of the wavelength.
- ILA has low impedance. In order to increase the impedance of ILA, another inverted -L element was incorporated, which makes it an inverted F antenna.
- Inverted-F Antenna
- By including the second inverted-L element, the input impedance of the antenna can be set to match the load impedance of the antenna.
- The drawback of the inverted-F antenna is the lack of bandwidth.
- ILA has low impedance. In order to increase the impedance of ILA, another inverted -L element was incorporated, which makes it an inverted F antenna.
Figure 4.9 shows a planar inverted F antenna in a 3-dimensional view.

Figure 4.9: The Planar Inverted-F Antenna
f1 = resonance frequency when W = L1
fr = resonance frequency
fr decrease as W decrease.
fr depends on:
The width of the short circuit plate – width increase, fr/f1 increases
size ratio of L1 and L2 – L1/L2 increase, fr/f1 decrease
Three cases to easily formulate resonant frequency expression of PIFA
case 1) when W = L1, L2 + H = λ/4
case 2) when W = 0, L1 + L2 + H = λ/4
Case 3) When 0 < W/L1 < 1, the resonant frequency fr is a linear combination of the resonant frequency associated with limiting cases.

The bandwidth depends on;
- The size ratio of L1/L2: L1/L2 increases, and bandwidth increases.
- The height of the short circuit plate H: H increases, and bandwidth increases.
- Ratio W/L1: W decreases, bandwidth decreases.
PIFA is assumed to be mounted on an infinite ground plane.
Technique to widen the bandwidth of MSA;
- Increasing H increases bandwidth; however, size increases. For MSA, an increase in substrate thickness leads to the excitation of surface waves, which causes a loss in radiation efficiency.
- Lowering the dielectric constant value will result in an increase in the bandwidth.
- Unloaded Q is proportional to ԑr, and bandwidth is inversely proportional to Q.
For this tutorial, we are designing a Meandered PIFA. The meandering technique is generally used in an antenna design to save space. On top of that, the meander line also helps to generate resonance at two frequencies.
4.3.2 Design Requirement of Meandered PIFA
- Design Parameters
- Frequency range
- 4G and 5G Bands covered
- Input Return Loss (S11)
- Radiation Efficiency
- Design Specification
- 746MHz – 960MHz and 1.71GHz to 2.69GHz
- B1, B2, B3, B4, B5, B7, B8, B13, B18, B19, B20, B25, B26, B27, B38, B39, B40, B41, B66.
- < -6dB[/av_cell][/av_row] [av_row row_style='' av_uid='av-awm5ug'][av_cell col_style='' av_uid='av-8zqql4']Gain[/av_cell][av_cell col_style='' av_uid='av-74ets8']> 2dBi
- > 90%
4.4 Step 3: Antenna Optimization
We are going to design a meandered PIFA antenna for this tutorial. We will build the meandered PIFA and optimize the PIFA to meet all our design parameters.
Layout optimization is called parametric EM simulation in ADS. There are two ways to do a Parametric EM Simulation in Keysight ADS. The first method is to create a schematic using “TLines-Microstrip” palette components, followed by creating the layout from the schematic. The second method is to create the layout in the ADS layout straight away. We will use the first method for this tutorial.
The first step for creating and optimizing an antenna using method one is to draw the antenna shape you want to design in the ADS schematic using components from the “TLines-Microstip” component palette.
A new schematic needs to be launched to build the antenna. The next step is to navigate to the “TLines-Microstrip” component palette. You can find many types of microstrip lines. It will help create the unique antenna shape design we want. We start by placing MLOC onto the schematic, then MCORN, MLIN and MTEE. We can copy and paste the same shape to repeat the same step. After you copy, before pasting onto the schematic, you also may need to rotate the microstrip lines so they will have the correct angle for placement. We are creating the horizontal meandering element of the PIFA antenna. Since it’s meandered, it won’t be the exact quarter wave in length, as explained earlier in this tutorial, because the meandered line will have a shorter length than a straight line.
Meandered Planar Inverted-F Antennas (PIFAs) are a specialized variant of the traditional PIFA, where the horizontal radiating element is meandered. This design modification can offer several benefits, particularly in terms of size reduction and enhanced performance. Here’s an in-depth look at meandered PIFAs:
The horizontal line of the PIFA is not straight but instead follows a meandered or zigzag pattern. This increases the electrical length of the antenna without significantly increasing its physical size. Like a traditional PIFA, the Meandered PIFA also includes a ground plane, a shorting pin, and a feed line.
The meandering of the radiating element effectively lowers the resonant frequency, allowing for a more compact design. This is particularly useful for applications requiring a small form factor.
The meandered design can affect the bandwidth and efficiency of the antenna. Optimizing the meandering pattern can help achieve desired performance metrics.
The primary advantage of meandering the radiating element is the reduction in physical size while maintaining or achieving a desired resonant frequency. Meandering can improve impedance matching and radiation efficiency, especially in confined spaces. The meandered pattern provides flexibility in design, allowing for better integration into complex device architectures.
We have to place both the positive and negative pins in the schematic. The positive pin goes to the feed, whereas the negative pin goes to the ground plane.
When trying a unique shape, you might have to try it a few times before getting the correct shape. After placing the microstrip components, we connect them together using wire.
When the microstrip lines’ component text collides, we must separate the components’ text because we will edit the component parameters later. Editing becomes easier when you clearly see the component’s text.
Four “TLines-microstip” palette components were used in the design. Those are MLIN, MLOC, MCORN and MTEE_ADS. MLIN is a basic microstrip line, which is a straight line with a width and length. It has two connection points at both ends.
MLOC is a Microstrip open-circuited stub with an open end on one side and a connection point on the other. Similar to MLIN, we can define the width and length of the MLOC.
The MCORN is a 90-degree Microstrip Bend with two connection points and a width to be defined. The MTEE is a Microstrip T-Junction. We can set three different widths for three different connection points on the MTEE.
Figure 4.10 shows the completed schematics with parameterization.

Figure 4.10: The completed Schematic with parameterization
The next step is to parameterize the design. To do that, let’s first create or define the parameters we want to use in the design. To create parameters, we have to go to File -> Design Parameters.. -> and click on the Cell parameters tab. Here, we can enter the parameters you want to use in the design one by one. It could be a lengthy process, depending on the complexity of the design.
Most new items you define need parameters. Each parameter has characteristics that determine how it is handled when the item is used. These include the name and label displayed in the Component Parameters dialog box, the unit type for the parameter, the type of value assigned to the parameter, the default value, and certain control attributes.
Parameters can be defined in the Cell Parameters tab. If you check the Copy Component’s Parameters in the General tab, then there will be a list of defined parameters in the Cell Parameters tab. These parameters may be modified here. In addition, you can add or cut parameters. Figure 4.11 shows the definition of the design parameters and the cell parameters tab.

Figure 4.11: Design Parameters definition
Let’s talk about how to create new parameters. The most important things we need to define in the Cell parameters tab are given next.
By default, the “parameter name” tab will be empty when you start defining a parameter for the first time. You need to define the parameter here by giving it a name. For value type, you can select the parameter to be real, integer, complex, or string. For our design, we will leave it as Real. The parameter Type/Unit is optional, so you can leave it unitless or assign a unit. The unit can be length, frequency, time, angle, etc. Since it’s optional, we will leave it unitless for our design.
The default value contains the default value of a parameter. It is recommended that the unit be inserted together with the default value in this box. The default value unit can be in mil, mm, cm etc. We have to select the “Display parameter on schematic” option to display these parameters on the schematic.
We also need to select the “optimizable” option to allow these parameters to be optimized.
Allow Statistical Distribution is Selected by default, but this option is only needed if you intend to do post-production tuning for these parameters during yield analysis.
The parameters I’m optimizing for meandered PIFA antennas are only two kinds. Those are width and length. For simplicity, I defined width as X and length as Y. A unique number is given at the end of X and Y to differentiate different elements of the meandered PIFA.
We start by inserting the parameters into the appropriate microstrip schematic components, as each unique parameter is created for each microstrip component. I’m inserting the correct parameters into the respective microstrip lines.
If you recall, previously, we defined the default value with unit, mil. Due to this, the microstrip schematic components should not have the unit on them; otherwise, they will have double units, which will result in wrong width and length parameterization.
Due to this, the correct way to insert the Width and length parameters into the microstrip schematic component is by doubling-clicking the component and inserting it. While inserting, the unit will disappear. Since our intention is to get rid of the unit, we can ignore this.
Each component parameter is inserted individually by double-clicking on it to launch the “Edit instance parameters”. Figure 4.12 shows design parameters insertion into the schematics.

Figure 4.12: Design Parameters insertion to the schematics
There is a shortcut way to quickly edit component parameters. Before this, we have been clicking apply and ok after updating each component parameter. However, it’s adequate just to click Apply. After clicking apply, the parameter for the microstrip component will be updated. Instead of clicking ok after that, you should select the next component, modify the width and length, and click apply. This process can be repeated to accelerate the updating process of the microstrip component parameters.
I have given a unique number for each microstrip component’s width and length to identify them easily. This way, I’m able to update them quickly.
As you can see, I’m inserting the ground plane dimensions now. It is not parametrized because I’m not planning to optimize the ground plane size.
We have completed the insertion of the parameters to the appropriate microstrip components. Next, MSUB is inserted to define layers of the PCB. This is a four-layer rigid PCB with the antenna located on the second layer. After inserting MSUB, enable Cond1 in all the MSUB because that’s where the layer is defined. Cond is our top layer, followed by M2, the second layer; next is M3, the third layer; and finally, cond2, the bottom layer. These layers are defined in order from Msub1 to Msub4.
Since we decided to place the antenna on the second layer, M2, let’s move the microstrip lines or antenna to the M2 layer. This is done by changing the Substrate to MSUB2.

Figure 4.13: MSUB definition
I’m manually changing the substrate of each microstrip schematics component to MSUB2 to move the antenna from the first layer to the second layer.
Before moving to the next step, it’s a good practice to check to make sure all the parameters are correctly inserted.
Our schematic is ready. Finally, we can create and update our ADS layout from this schematic. This is done by clicking Layout -> Generate/Update Layout.. and clicking Apply.
The layout is successfully generated, and it looks exactly like the way we want it to be as shown in Figure 4.14, which is good news.

Figure 4.14: layout generated from the schematics
We have a trace on the top layer connecting the antenna from the second layer. Due to this, we need a via for this connection. I could have done the via connection in the schematic, but I chose to do it in the layout. You can connect the via in the schematic as well.
To place a via, go to insert -> via. By default, through hole via is available. Change it to specify top/bottom layers and select the second layer as the bottom layer. Your cursor now has a via, and all you need to do is place the via in the right place.

Figure 4.15: Via placement in the design
Since we created our layout from the schematics, we should check if our layout is parameterized by going to EM -> Component -> Parameters… Under design parameters, you can see all the parameters you created in the schematics.

Figure 4.16: design parameters
The next step is to set up the EM Simulation. We will launch the EM Setup and choose our preferred EM simulation setup. However, there is an error message here. It says that no ground plane was found in the substrate definition. This can be fixed in the port editor. Right now, two ports have been found, but P2 is actually the ground reference pin of the P1, so drag P2 and drop it in the gnd of P1. This issue should be resolved now.
Let us set up our optimization. FEM EM simulator is chosen for the simulation.

Figure 4.17: EMSETUP EM Simulator
Let’s define the frequency range and frequency points of interest. The frequency range of our interest is 0.5GHz to 4GHz, and I want to add a few frequency points to the simulation. These are single-frequency points which I would like to get the results.

Figure 4.18: EMSETUP frequency definition
Let’s leave all other settings to default. We can save and exit the EM setup. Finally, we create an EM model by clicking EM -> component -> Create EM Model and Symbol..
Let’s create another schematic to place the EM model and optimize it. Drag the EM model and place it on the schematic. I don’t like the layout look-alike symbol created by default, so I will change it to a dual-port symbol.
To place the S-parameter simulation controller and port one shot, click on Insert -> Template and select the S-parameter template.
I’m deleting the unnecessary component in the schematic, which is the Display template, and also Term2. After that, the Term 1 is connected to the EM Model.
The S-parameter simulation controller frequency is defined next. Similar to the EMSetup, we set the frequency range to be 0.5GHz to 4GHz. The frequency step we are setting is 100kHz.
Next, we have to redefine the parameters for optimization. To do this, we need to insert the VAR or Variables and Equations Component first.
After that, we need to redefine the parameters again. I will redefine the parameters in the same order for simplicity. The X and Y in the EMModel are redefined as A and B in the VAR, respectively. The number behind is the same between X and A and Y and B.
The values of X1 and A1 are equal, the values of X2 and A2 are equal, and so forth.
In the same way, the values of Y1 and B1 are equal, the values of Y2 and B2 are equal, and so forth.
After that, insert the newly created parameters in the EMModel. After modifying one parameter, press enter to arrive at the next. This parameter redefinition is done because the optimization can only be done via a VAR.
Next, on the VAR, we have to enable optimization and set the optimization range for each parameter. Each parameter will be assigned an optimization range with minimum and maximum values. Since we are doing continuous optimization, there is no step value to assign.
The last step before starting optimization is placing OPTIM and Goal in the schematic. Optimization controller or OPTIM and goal can be easily searched in the search all libraries by just typing OPTIM and GOAL.
Set the goal to optimize S11 to be less than -10dB across the frequency band of interest, which is 746MHz to 960MHz and 1.71GHz to 2.69GHz. When entering the frequency, the units should be entered together. Since we have two different frequency ranges, each frequency range will have a separate limit.
With this, all the steps required for running an optimization have been successfully completed. The completed schematic is shown in Figure 4.19. Next, we just have to click a button to run the optimization.

Figure 4.19: Completed schematics for EM Model optimization
Just click on the optimize button to start the optimization. The optimization has been successfully started. With this, the optimization section of the antenna design comes to an end.
4.5 Step 4: EM Simulation
This is the optimization results. Since we optimized the antenna for a good S11, I have plotted the S11 in the data display server.
Our frequency band of interest is 746MHz to 960MHz and 1.71GHz to 2.69GHz. As you can see, The markers are not set at the correct frequencies, so I will move them manually. This can be done by selecting the markers and pressing up or down keys on your keyboard.
The antenna exhibits less than -6dB return loss across the frequency band of 746MHz to 960MHz and 1.71GHz to 2.69GHz, which indicates that the antenna meets the specifications as shown in Figure 4.20. I believe further optimization and tweaking will improve these results.

Figure 4.20: S11 of optimized antenna
In order to simulate the far-field parameters such as gain, directivity, and radiation efficiency, we need to do an EM simulation with the save fields option enabled. To do an EM Simulation, we need to generate a layout from the schematic. We are generating a layout from this schematic because it has the optimized antenna parameters. Generate the equivalent layout to the optimized schematic by clicking Layout -> Generate/Update Layout. When you click apply, the layout will appear.
The layout needs to be flattened so pins can be placed within. Pins are needed to create a port for the simulation. To flatten the layout, right-click on the layout, go to the component, and select Flatten.. A pop menu will appear with Options. Flatten all levels of hierarchy to shapes is the right option for this design, so we click apply and ok.
Since I already have a flattened layout with pins placed, I will delete the newly flattened layout.
Let’s take a closer look at the pins placed on the layout. You can place the pins by clicking Insert Pin.
Here is the port setup in the port editor.
The next thing to do is to set up the EMSetup. The EM simulator is set to FEM. The frequency range and frequency points are set to our preferred frequencies. The most important thing is that under the output plan, we need to enable save fields by selecting All generated frequencies or user defined frequencies. I choose All generated frequencies. The rest of the settings can be default as of now.
All the settings have been set before, and that’s why you are seeing a fully done EmSetup.
The simulation is executed by clicking Simulate, which is located in the EMSETEP under the model.
Since we are doing EM Simulation for six single frequency points together with the frequency range and also have the Save Fields option enabled for all the frequencies, this process will take time.
4.6 Step 5: Results and Analysis
Here is the return loss result again. This time, this is from the layout EM Simulation. We also got return loss results after optimization. As you can guess, both are similar. The return loss meets the specifications for the frequency band of 746MHz to 960MHz and 1.71GHz to 2.69GHz.

Figure 4.21: S11 of optimized antenna
Next, let’s look at far-field parameters. To get them, click on the far-field button as demonstrated. The Far-field simulation is in progress now.
Finally, the far-field simulation is completed, and the 3D radiation pattern and antenna 3D view are launched with the far-field results. The far-field GUI is shown in the Figure 4.22.
In the solution setup, you can choose the frequency of interest. After that, click far-field and Antenna Parameters to display all the far-field parameters, such as gain, directivity, and radiation efficiency for that particular frequency.

Figure 4.22: Far-field GUI
Figure 4.23 shows the Far-field results of 746MHz. At 746MHz, the directivity, gain, and radiation efficiency are 2.2dBi, 1.9dBi, and 94%, respectively.

Figure 4.23: Far-field results of 746MHz
Figure 4.24 shows the Far-field results of 960MHz. The directivity, gain, and efficiency are 2.5dBi, 2.3dBi, and 95%, respectively.

Figure 4.24: Far-field results of 960MHz
Figure 4.25 shows the Far-field results of 1710MHz. As I change the frequency, you will notice that the far-field radiation also changes. The directivity, gain, and efficiency are 5.3dBi, 5.1dBi, and 94%, respectively, for 1.71GHz.

Figure 4.25: Far-field results of 1710MHz
Figure 4.26 shows the Far-field results of 1990MHz. At 1.99GHz, the directivity, gain, and radiation efficiency are 6dBi, 5.8dBi, and 95%, respectively.

Figure 4.26: Far-field results of 1990MHz
Figure 4.27 shows the Far-field results of 2110MHz. At 2.11GHz, the directivity, gain, and radiation efficiency are 6.2dBi, 6dBi, and 94%, respectively.

Figure 4.27: Far-field results of 2110MHz
Figure 4.28 shows the Far-field results of 2400MHz. At 2.4 GHz, the directivity, gain, and radiation efficiency are 6.4dBi, 6.1dBi, and 94%, respectively.

Figure 4.28: Far-field results of 2400MHz
Figure 4.29 shows the Far-field results of 2690MHz. Finally, at 2.69GHz, the directivity, gain, and radiation efficiency are 7.7dBi, 7.2dBi, and 90%, respectively.

Figure 4.29: Far-field results of 2690MHz
Last but not least, you can also rotate the antenna’s 3D view and radiation pattern. This is the end of the Design and optimization of a 4G and 5G Antenna tutorial series. I hope you will like this.
For antenna design inquiries, please send us an email to info@innowave.co

